Видео

ME: Yawn. Time for bed. We have school tomorrow. BRAIN: lol no. we're going watch a video about a green roof ME: ok

Good video jimmy👌🏻

I just purchased a 4 year old home with a metal roof & on the rear section of the roof, the first row of screws horizontally begin 29 inches from the gutter. Should I be concerned?

This is the best comprehensive video on steel roofing I have seen! It very hard to find any guidance at all when I was roofing, I did nit all the details shown in this video but my roofs were guaranteed! Thank you!

Todo lindo con videitos y dibujitos...

❤❤❤❤❤👍👍👍👍

Very informative. Answered a lot of questions!

Great video! Most helpful for DIYers!

good job

Too much unnecessary complications !!

Which of these can I use to cut the glare on my ASC metal roof? Neighbors are unhappy.

No screws over the panels😅

It's "roof" not "riff".

IT WILL LEAK AT THE SCREWS YOU NEED METAL ROOF WITH CONCEALED FASTENERS, FASTENERS UNDER THE ROOF

With proper self stick water barrier laid first, screw will be sealed by under layment. In case of washer failure wood should still be protected

When the foam under the roof cap blows out? #@!%

Don't screw in the run of the sheet and instead of that foam that'll get eaten up by bats, just bend the top of the sheet backwards.

ruf

Installing metal roofing is such a practical and long-lasting choice for a home! Those 3ft panels from ASC Building Products must give a sleek and modern look, and the durability of metal roofing means less worry about replacements or repairs for years to come. It's great to see people taking on these kinds of home improvement projects. Keep up the fantastic work! 🏡🔨✨

WTF is a Ruff Panel?!

😂 the effort put into this video lends it credibility it really doesn’t deserve. The ends of the panels get hemmed and hooked to the correct drip edge for the panels, drip edge also isn’t correct. Come on guys, a homeowner might make me do something like this to their home after watching something like this.

Just beautiful.

They aure use a lot of butyl mastic tape. I don't see much of that used here in my part of New York State.

Thank you

You forgot counterflashing on your sodewall bud

It started off looking good then the morons show screws being fitted in the flat pan.

👍👍👍

Thank you 😊

Excelent

Has me stuffed why they say to screw the sheets down in the valley and not the peak, the rubber washer under the screw heads dont last for ever and always some get damaged while the screw is being screwed down.

Comment se présenterait le travail avec des panneaux sandwichs ?

I can not find a video that shows in detail how to properly close a metal valley when a lower ridge runs into the slope of a higher perpendicular ridge roof section. The mystery is how to seal the very top where the valleys intersect.

Sure would be nice to deal with a company that was in the business of making money by delivering a great product and satisfying customer needs, rather than focusing on feelings and "social justice"...but I guess if every company is being coerced into jumping on this political train then who cares if the rainbow/culture coalition (DEI, ESG) adds 10%-20% to the end product cost.

ทำได้แค่ในคอมทำจริงมึงจะขึ้นมุงอย่างไง55555

Excelent method

Z_

Let me put my caulk in it

This only stops rains, not hurricanes, I have been doing forensic architecture for the DoD, and I see them fail every time a hurricane passes through a base. After that, any heavy rain fall the interior of the building will be cover in pools of water or leak will came from the failure of the neoprene seals.

No purlins?

We tore down a 70 yr old commercial chicken house having a metal "5 V groove" metal roof. It had the old metal roof nails...all placed at the top of the V grooves...not in the valleys. The wooden structure was in remarkably good condition with no rotting. Placing fasteners in valleys is a no-no. I am wondering if an air gap underneath of approximately 3/4" would help cooling of the roof?

Well detailed thanks

铝铁混合结构。

You have some really awesome products in your part of the world

At 1:36, this guide tells you to install a line of screws through the panels and into the edge of the eave -- one of the first places roofs leak. If you want an el cheapo exposed fastener roof, why pay for standing seam?

This diagram has you cut some metal off to fit inside the first piece of flashing,but then it says to put caulking on it, then slide it under the first piece! This is physically impossible to have the second peice slide under the first yet have the trimmed off peice fit inside the outside crimped edge! It would have to go on top of the first peice and caulking would be applied to the first peice of eves flashing! I was sold a system that costs me more,and another company just uses drip edge for the edging,same as for a shingles roof. The point is,if you watch different videos on how to install a steel roof,if your paying attention you should notice there's 2 ways to do it! A 3rd is just not bother with eves flashing and the hardware you don't need,as your evestrough covers most of the wood under the roof as well as metal or vinyl soffit put under the overhang !

Супер😊😊😊

1inch screws are never long enough should be 2or2@1/2 inches I have a friend with a pole garage over time freeze and thaw and wind worked the ends of the panels loose and caused leaks we replaced the screws with longer ones to fix the problem just a thought

好清楚...讚

Verry good👍, thank's for vidios, verry important for me,

I agree leaks happen placing screws in valleys.